2020 PETERBILT 367 TWIN STEER WITH 44″ SLEEPER
POWERED BY THE CUMMINS X15 PRODUCING 565HP AND 1850TQ
One (1) only – New Weldco WHL45TC100 stiff boom crane complete w/ the following:
Maximum Lifting Capacity of 80,000 Pounds @ 10’ Radius
Four-Section Telescopic Boom 30’6” to 100’
Polymer Sheaves for Extend/Retract & Hoist Cables
Replaceable Composite Rub-Pads
Pre-Tubed for Future Boom Lighting (lights not included)
Maximum Sheave Height of 110’
360 Degree Area of Operation
Continuous Rotation c/w 5-Port Hydraulic Swivel / 26-Channel Electric Swivel
15,000 lbs 2-Speed Planetary Winch w/ 500’of 5/8” Non-Rotational Wire Rope
Swing Around Operator Control Station.
Fully Enclosed “New Style” Swing Cab w/ Diesel Heater.
Fixed Front Windshield w/ Wiper, Washer & Cover
Opening Skylight & Opening Rear Window.
Electric Slide-Out Crane Cab Step.
2-Camera’s (w/ one display in crane cab) To View Rear Right Outrigger Leg & Winch.
Boom Length & Angle Indicators
Boom Rest w/ Hydraulic Reservoir Mounts
Hydraulic Dual Axis Joystick Controls
Hydraulic Oil Cooler c/w Dual Fan & Thermostat.
Radio Anti-Two Block w/ Lockout
LMI System w/ Operator Display
Factory Supplied Tractor Mount Lower Frame.
4 – Out & Down Outriggers – 24.75’ (7.53 m) Spread
Pressure Compensated Piston Pump c/w Dedicated Gear Pump for Swing Circuit
110 Gallon Hydraulic Reservoir w/ Suction Strainer & Shut-off Valves
Operators Service / Parts Manuals
Installed on Customer Chassis w/ Air Shift PTO, All Hydraulic Plumbing, Oil & Testing
40 Ton 4-Sheave (Easy Reeve) Hook Block.
*Jib not included.
One (1) only – Custom NWC 45 ton rig up complete w/ the following:
Supply and install two front aluminum cabinets 27”X 26”X 54”
Cabinets to have 1 divider, two half shelves & “J” hooks, interior lighting but no cabinet
Center partition has the factory hydraulic tank mounted.
Supply and install drop boxes 1 per side (48” long X 12”high X29” wide) c/w anti slip
coating on top
Supply and install aluminum vented grating from cabinet to front edge of picker.
Perimeter of walking deck to be tubing with the appropriate amount of clearance lights
inset in tubing
Supply and install one set of 4 loops per side tire chain hangers with mud flap protection
over top of fuel tanks
Supply and install two sets of staircase style steps over top of fuel tanks
Supply and install two outrigger pad holders for 30″ pads
Supply and install steel swing around rear headache rack, c/w locking chain hangers,
chain baskets, two snipe holders, four sling-holders. Clad rear headache rack with
aluminum inserts. Supply and install two back up lights, adjustable on rear headache
rack. Supply and install two per side round stop turn lights and three clearance lights
across the middle of the winch weldment
Install sliding fifth wheel supplied with truck and weld in place
Install supplied airlines and trailer cord to fifth wheel area
Supply and install rear apron c/w pin hitch, ramps and one stop/turn light and one back
up light per side
Supply and install custom-made polished aluminum checker plate rear fenders full
length. Split fenders in three pieces
Install mud flaps front and rear of fenders
Custom aluminum checkerplate covers for the outrigger boxes
Supply and install 3-boom tip and 2-turret mounted lights under cab. Run wiring in
Supply and install Aluminum grab handles on tool box for access to deck.
Supply & install 1 per side flip-over steps on rear fenders (for access to headache rack)
All stop/turn and clearance lighting to be LED
Blast & paint rig-up with black Endura
CONTACT YOUR LOCAL SOUTHERN ALBERTA PETERBILT SALESMAN TODAY